S50DX napisal/-a:Je kaj novega... Tako na oko?
Ponavadi vse to piše v changes.txt
CUL, Danilo S50U
Changes since ver 2.5.0 as of 9 Dec 05
=====================================
1) The centre cell used for Sunrise/Sunset in the upper of the lower status bars, had a right click menu and you could paste data into that cell. Bug cleared
2) Modified the URL for NOAA information to "http://www.sel.noaa.gov/ftpdir/latest/wwv.txt"
3) The code to prevent the antenna direction indicator being shown on the Miller projection maps only worked for the ARSWIN and not a DSU-1 ... Bug cleared
4) Support for the DXCC Challenge. See new Menu option under AWARDS.
5) Previously there was a minor problem with the compass display on the Tracking Window where the text (000, 015, 030, 045, etc) was a couple degrees out of alignment. This problem should be corrected (you'll need to re-create the maps to see the corrected display). Also, compass now marked every 5 degrees.
6) The MMVARI engine has been integrated into Logger32.
a) The notch is turned On/Off by clicking on the menu item.
b) Right click on the Waterfall/Spectrum action has changed -
i) If Net is On, it works like the $align$ Macro, and centers the signal.
ii) If Net is Off, The TX offset is put on that frequency.
iii) If TX offset freq is showing, click Net to On, and you will be transceive.
c) The $align$ macro only works if Net is On. The Macro list has been expanded to cater for the new modes/facilities.
7) Telnet/Cluster TALK and ANNOUNCE messages can now be saved to a log file. See new menu options, select the MESSAGES Tab of the Cluster Window. Right click on either the TALK or ANNOUNCE pane. Files used for logging are TalkMessages.txt and AnnounceMessages.txt in the default Logger32 directory. No facility is provided to open/read these files from within Logger32, It is suggest that the user create a desktop shortcut for this purpose.
8 ) Previous equal sign entries for a given call did NOT show up in the Previous QSOs window when entered in the Log Entry window Callsign field.
9) DX Spots from a SH/DX/xx xxx command are now shown in chronological order.
10) Previously DX Spots from a SH/DX/xx command were not checked for duplicate spots. From this version, DX Spots from a SH/DX/xx command will only show in the DX Spot Window if the Show SH/DX/xx option is enabled and the DX Spots returned are not already in the DX Spot Window.
11) Included the capability of NOT showing DX Spots from a SH/DX/xx command in the DX Spot Window ( for those who want to collect the info in the telnet window but not have the information mess up the dxspot list.)... See new menu option - Right click on the DX Spot Window and mouseover SETUP
12) Corrected a bug found in the QSO reporting in the upper of the lower status bars [bug correction]
13) Users can now enter a 6 figure gridsquare reference to set up "my QTH Lat/Long".
14) Previous QSOs Window is now activated when ADDing QSOs.
15) The MMVARI sound card sample rate uses the default 11025Hz. For those with slow PCs, this is too high, and they need to run the sample rate at (say) 6000Hz. For those with fancy new radios that have optical interfaces, they need a sample rate of 48000Hz. In this version, the sound card sample frequency can be set to other than the default 11025Hz by editing the Logger32 INI section [MMVARI] and adding the line "MMVARI Sample Frequency=xxxxxx" (where xxxxx is the frequency).
Example:
[MMVARI]
MMVARI Sample Frequency=48000
16) Bug fixed in the Band Map window. Previously when the Band Map is fully populated, the automatic selection of showing the newer spots (and discarding the older spots) did not work reliably.